CRL FW632RS Universal Crank-Out Van Window 41-1/4" x 25-3/4"

CRL FW632RS Universal Crank-Out Van Window 41-1/4" x 25-3/4"

*** Back Ordered Estimated Shipping Mid to Late April ***

Part # FW632RS
MFG: CR Laurence (CRL)

MFG Country: USA

Warranty: 30 Days

Glass Color = Solar Privacy Glass 

Glass UV Rating = 28%

The Universal crank-out Van Window is extremely popular on Camper Van conversions , with its dark solar privacy glass that goes right to the edge for a flush look and its abundant air flow. The internal structural framing of the FW632RS has a black powder-coat finish, concealed from exterior sight by the silk-screened black fade edge of the privacy glass. The entire window is contoured to match the sidewall or door of most vans, making installation as simple as conventional fully framed windows with out the old style look. The Crank Out Awning Style Window features state-of-the-art operating hardware to open the lower panel of glass allowing great airflow and the internal screen keeps bugs out great for the campsite. This model of Van Window is available to fit the forward and rear driver and passenger side rear panels. 3" (76 mm) corner radius, for 1/8" (3 mm) wall thickness.

• Awning Window Opens Approx 7" 

• Screen is 37-1/2 x 6-1/2" for great Ventilation. 

• Outside Frame Dimensions: 41-1/4" X 25-3/4" (1048 x 654 mm)
• Cut out Dimensions: 40" X 24-1/2" (1016 x 622 mm)
• Clamp Ring/Angles: 1/8 (3 mm) Angles

 No Additional Accessories Required 

 To install the FW/VW Series of windows you will need to create a template. To make a template you can either use the aluminum framing on the backside of the window or the clamp ring we will have illustrations on using the clamp ring. Be sure to use the edge of the clamp ringthat matches to the aluminum frame edge of the window (the aluminum frame that goes through the wall). 

Make sure that the clamp ring is taped shut as it has an opening. 

 You will then trace you template onto the cardboard box sharpie, black marker ,etc.. you do not want to have to thick of a marker as you want to try and be as precise as possible. 

After you have draw out the pattern on the cardboard it is time to cut the pattern from the cardboard. 

Once you template is created clean up any little rough edges and we are ready to place on your van. You will want to measure out for placement to insure you have your template where you want it to be. To hold template in place you can put screws through cardboard to hold, have a partner hold or use tape. In our photo we used tape. Be sure to tape the template in place on the straight areas so those are easy to draw in your line later.

Draw your template onto the wall of the van. 

Once you have drawn your pattern onto the wall of the van and are happy with the placement your ready to cut. Reciprocating saw, skill saw, disc, nibbler,shears, etc... 

Once your hole is done dry fit the window to make sure window fits into hole no adjustments or extra trimming are needed. If your good you can add clear coat or paint to the cut edge its not necessary just a precaution. 

If you window is good to go you will attach the van window installation foam to the back side of your window

Now time to install the window. Before putting the window on the van its best to go through make a small pilot hole in all the locations around the trim ring that way you do not round the heads of the screws when tightening the window. 

Put Window in place from outside of Van allowing the aluminum mounting frame to extend through hole in wall. Place clamp ring from inside most vans will have the split on the bottom. With one person holding window in place on the outside the other can start to screw from the inside generally start with the two at the split in the trim ring to have that lined up then top and around you do not want to fully tighten once all screws are in place, you can then go back around and tighten them be sure to tighten evenly around for proper seal.