CRL Universal Non-Contoured Horizontal Sliding Window 25-1/4" x 16-3/4" with 2-1/4" Trim Ring VW8249
**Back Ordered Estimated Shipping April 2021**
Part # VW8249
Mfg: CR Laurence (CRL)
MFG Country: USA
Warranty: 30 Days
Glass Color = Solar Privacy Glass
Glass UV Rating = 28%
This window is to use with a 1/8" thick wall(straight to van sheet metal) or a 2-1/4" Thick wall, often a wood, foam,metal spacer is required for installation.
- Dark Solar Privacy Glass
- Black Powder-Coated Frame
Our CRL Universal Flat Surface Windows are the "all-purpose solution" to ventilate and increase visibility in just about any vehicle with flat walls. The frames are made of extruded aluminum with a black powder-coated finish. The metal is then formed to surround Dark Solar Privacy Glass. The sliding panel has a positive locking latch for security, and the ventilating panel is screened to let air in and keep bugs out.
Outside Frame Dimensions: 25-1/4" (641 mm) x 16-3/4" (425 mm)
Cut Out Dimensions: 24" (610 mm) x 15-1/2" (394 mm)
Clamp Ring/Angles: 2-1/4" (57 mm) Reversible to 1/8 in (3 mm) - Rectangular 90°/90°
|Whats needed to Install?|
|How will I install this window?|
To install the FW/VW Series of windows you will need to create a template. To make a template you can either use the aluminum framing on the backside of the window or the clamp ring we will have illustrations on using the clamp ring. Be sure to use the edge of the clamp ring that matches to the aluminum frame edge of the window (the aluminum frame that goes through the wall).
Make sure that the clamp ring is taped shut as it has an opening.
You will then trace you template onto the cardboard box sharpie, black marker ,etc.. you do not want to have to thick of a marker as you want to try and be as precise as possible.
After you have draw out the pattern on the cardboard it is time to cut the pattern from the cardboard.
Once you template is created clean up any little rough edges and we are ready to place on your van. You will want to measure out for placement to insure you have your template where you want it to be. To hold template in place you can put screws through cardboard to hold, have a partner hold or use tape. In our photo we used tape. Be sure to tape the template in place on the straight areas so those are easy to draw in your line later.
Draw your template onto the wall of the van.
Once you have drawn your pattern onto the wall of the van and are happy with the placement your ready to cut. Reciprocating saw, skill saw, disc, nibbler,shears, etc...
Once your hole is done dry fit the window to make sure window fits into hole no adjustments or extra trimming are needed. If your good you can add clear coat or paint to the cut edge its not necessary just a precaution.
If you window is good to go you will attach the van window installation foam to the back side of your window
Now time to install the window. Before putting the window on the van its best to go through make a small pilot hole in all the locations around the trim ring that way you do not round the heads of the screws when tightening the window.
Put Window in place from outside of Van allowing the aluminum mounting frame to extend through hole in wall. Place clamp ring from inside most vans will have the split on the bottom. With one person holding window in place on the outside the other can start to screw from the inside generally start with the two at the split in the trim ring to have that lined up then top and around you do not want to fully tighten once all screws are in place, you can then go back around and tighten them be sure to tighten evenly around for proper seal.
** If using a wood frame / spacer same installation process just have the wood between inner wall and clamp ring.
|Windows will generally ship in 1-3 Days , shipping time is 1-5 days. Windows will ship via UPS,Fedex , or Freight Truck.|